Thursday, December 20, 2007

Greenhouse statistics


Cold day atop Mont Merde: the greenhouse is MUCH taller than it appears in this picture

Many have asked, so here it goes:

Coldframe, high tunnel, hoop house, polytunnel: we just call it The Greenhouse. Folks: It will add a zone and a half to your growing season. My 6B garden? An 8A, people...Panhandle Florida!

I got the greenhouse kit from an outfit in Tennessee called Grower's Solution. The guy on the phone was both supremely friendly and extremely kind, answering my myriad questions as well as easily and quickly supplying a hardware shortage (one measly part!). I had hoped to use a local manufacturer for my greenhouse, but my request was a small one, and the local outfit doesn't deal with little orders like mine. Sigh.

The goods: It's 16' wide, 20' long, about 9' high in the center, and is composed of six bows (arches) that are set in ground stakes 4' apart. For ease of shipping, the bows are in three pieces: you screw them together to create one bow. It has one central purlin (center pole) that ties the bows together. If it were self-standing and 4' longer, it would require more bracing; as it is, it relies on a building for its one end and it is free-standing at its door end. For ventilation, I purchased one hand-rolled side (it rolls the plastic up about 4' off the ground on one long side) and created one large gable vent above the door.

You are supposed to supply the ground boards and the end framing for the end wall (in wood); they supply the plastic to cover the whole thing, and the channels and wiggle wire to hold the plastic to the bows.

We (i.e., nonmotivated husband and myself) hammered in the ground stakes, screwed together and erected the bows, and attached the purlin in under two hours. It was Instant Gratification, I do not lie. But then it was my work from then on: I excavated the ground on 3 sides to both bury hardware cloth and the 2x8 wood ground anchor and then erect the 2x4 notched studs for the end wall/door framing. This actually took me two whole days to do...separated by a week, of course, because, really, who has two full days to work on anything?

Putting the plastic on was another battle with the husband (that is, getting his free time). He committed finally on a day that was windy: I advise you not to put plastic on a greenhouse in the wind. Ever. But that was our fate. We anchored the plastic to the endmost bow (against the building) and then went from bow to bow until we reached the door end, kind of like pulling pantyhose over a reluctant leg. That wiggle wire is quite amazing stuff. It really is great at holding down the plastic film. The film is graded to last of 6 years without significant UV decomposition: I have heard neighbors say they've gotten 8 years of use, which rather helps me, as plastic is not exactly the most eco-friendly of things. We held the plastic down to the last bow with some pre-soaked 1x2 furring strips.

I say this all with a rather blase' attitude. I here admit that I am a builder of many things: neither construction nor power tools intimidate me (hahahaHA), but, well, if you have never held a hammer nor worn a toolbelt, then putting up your own greenhouse could be a challenge. (Compared to building our coop? This was a walk in the park.) But I will say that Tom's purchase of a hammer drill greatly eased our pain: it helped put the bows together and helped put the channel atop the bows in, like, no time at all. I had gone along just fine with my 14 amp cordless drill for two houses' worth of renovations; Tom has helped me see the light with his 18a Drill of Pain. I admit, I was impressed. (I still like mine better.)

Am I saying you all need to go out and erect a hoop house in your backyards? Well, absolutely! (I'm getting salads and veggies out of my garden in late December, are you?) Just read this guy's books, read his wife's gardening columns and book, and yes, you too shall Sip The Kool-Aid.

6 comments:

Anonymous said...

Hey, we've got the same drill. I like you couldn't understand why we needed it. Until we used it to put up the shed roof for the wood pile. Then I got it.

Nice tunnel - can't wait until we have enough room for one of those. Then we'll be right there with you in the Florida zone...

Dancingfarmer said...

Someday El I hope to have my very own tunnel too. I have to admit--like you---the plastic is the only "downer" for me. As you said though at least it lasts a long time. Until then--a couple of cold frames will work for me because after all it is warmer here than were you are :-D
Monica

Shayne said...

I grew up a country girl and living on my 1/12th of an acre in Livonia is getting old and yes I want a greenhouse and chickens in my back yard.

Robin (Bumblebee) said...

Hi El,

I admire your adventure. Frankly, if we get anything that involves big tools around here, we have to call Walter, the handyman. I can weed, plant, weed, deadhead, weed, plant some more. My husband can, well, eat. Walter does all the big stuff. But I GREATLY admire the can-do attitude of hearty folk with tools.

BTW, we're still waiting for the builder on our chicken coop. It's looking more and more distant...

I am still hopeful for spring chicks though.

Robin at Bumblebee

markali52 said...

I have a small greenhouse I put together from a homebase diy online kit I grow tomatoes in it at the moment bout never had much success.

BTMA Oil Press said...

A coconut crushing machine is a specialized apparatus designed to efficiently process coconuts for various applications. This mechanical equipment is engineered to break down coconut shells and extract the valuable coconut meat or copra within. Typically featuring strong blades or crushers, the coconut crushing machine ensures a thorough and uniform breakdown of the hard outer shell, facilitating easy access to the nutritious interior. In addition to extracting coconut meat, some advanced machines may also separate coconut water or milk. The coconut crushing machine streamlines the labor-intensive process of manual coconut opening, offering a more efficient and time-saving solution for industries involved in coconut-based product manufacturing or for individuals seeking to extract coconut ingredients at home.